PlantBot User Guide
Skip to guide

PlantBot User Guide

Set up your PlantBot, choose a growing mode, understand its interactions, and that's it.

  • 3 growing modes
  • 100+ emojis
  • 100+ supported plants
PlantBot with a plant and animated face

01 · Unbox

In the Box

Check that all items are present before beginning setup.

PlantBot, USB Type-C cable, inner pot, and user manual

02 · Controls

Overview & Buttons

Buttons 1 and 2 sit on the front. The charging port and Reset Button are located on the back.

Front and back diagrams showing PlantBot controls and charging port
1

Power

Press and hold Button 1 to power on or off.

2

Next

Press Button 2 to proceed or switch interface.

1×3

Network

Press Button 1 three times to reconfigure the network.

R

Reboot

Press the Reset Button to reboot the device.

03 · Get started

Setup & 3 Modes

Follow PlantBot’s on-screen instructions and select the mode that matches what you are growing.

1

Power up PlantBot

Turn on PlantBot and follow the instructions shown on-screen.

2

Download the app

Download “Tuya Smart” from the app store.

3

Select a mode

Choose Seed, Cuttage, or Plant.

PlantBot mode-selection screen

1 Seed Mode

Prepare a seed pack and follow the on-screen instructions.

2 Cuttage Mode

Prepare plant cuttings and follow the on-screen instructions.

3 Plant Mode

Prepare a 4-inch plant and follow the on-screen instructions.

04 · Before planting

Important Tips

Wi-Fi

Use 2.4 GHz Wi-Fi

PlantBot supports 2.4 GHz Wi-Fi. Do not use a 5 GHz Wi-Fi network.

Soil

Use suitable garden soil

Use garden soil provided by PlantsRobot or purchased from a professional shop. Do not use outdoor soil.

H₂O

Fill the water tank

Do not water the plant directly. Pour water into PlantBot’s water tank.

05 · Interact

Features & Interactions

PlantBot responds to touch and nearby gestures, while emoji and voice prompts help guide plant care.

Touch the leaves

Ensure the soil is moist, then gently touch the leaves. PlantBot will respond.

Make a gesture

Perform any gesture within 9.8 in / 25 cm of the front of PlantBot.

Watch and listen

Emoji and voice prompts guide plant care, such as moving PlantBot to a cooler spot.

Playful Alert

Playful alert as your setted time

Pet System

Take care and interact with PlantBot, it will unlock more icons and emojis

06 · Library

100+ Emojis & 100+ Plants

07 · Read before use

Important Safety Instructions

Keep PlantBot indoors, dry, away from heat, and protected from impact or unauthorized alteration.

  1. This product is intended for indoor use only. Do not use it outdoors.
  2. Do not submerge or partly submerge the product in water or other liquids.
  3. The battery may present a fire or chemical-burn risk if mistreated. Do not disassemble, short contacts, heat above 140°F (60°C), incinerate, or dispose of in fire.
  4. Do not expose the product to fire or any heat source.
  5. Do not disassemble or alter the product.
  6. Do not drop, hit, or subject the product to a strong physical impact.
Plant wellbeing notice. Many factors may contribute to plant wellbeing. PlantBot will do its best to provide effective instructions, but PlantsRobot cannot guarantee plant health.

08 · Compliance

FCC Information

The FCC warning is retained in an expandable section to keep the main guide easy to scan.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, determined by turning the equipment off and on, try one or more of the following:

  • Reorient or relocate the receiving antenna.
  • Increase separation between the equipment and receiver.
  • Connect the equipment to an outlet on a circuit different from the receiver’s.
  • Consult the dealer or an experienced radio/TV technician.

FCC Radiation Exposure Statement. The device has been evaluated to meet general RF exposure requirements and may be used in portable exposure conditions without restriction.

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

09 · Specifications

Product size
5.39 × 5.39 × 5.2 in (137 × 137 × 132 mm)
Battery capacity
2200 mAh
Battery type
Lithium rechargeable battery
Input voltage
5 V
Charging port
USB Type-C
Nominal temperature
41–95°F (5–35°C)

10 · FAQ

Which Wi-Fi network should I use?
Use a 2.4 GHz Wi-Fi network. Do not use 5 GHz Wi-Fi.
How do I reconfigure the network?
Press Button 1 three times.
How do I reboot PlantBot?
Press the Reset Button on the back of the device.
Where should I add water?
Pour water into the water tank. Do not water the plant directly.
What soil should I use?
Use garden soil provided by PlantsRobot or from a professional shop. Do not use outdoor soil.
What should I do if the screen freezes?
Use a pin to click the Reset Button located inside the small hole at the rear. The device should restart and reconnect automatically.

11 · Support

Need more help with PlantBot?

Contact PlantsRobot support